 | HP Compaq 6515b Notebook PC
Workstation Hewlett Packard Company | 23 Jul 2007
90854 |
YES CERTIFIED with the following products:
Operating Systems:
| SUSE® LINUX Enterprise Desktop 10 for x86 Service Pack 1 for SUSE® SLED 10 |
Product Description
Refer to www.hp.com for more details
Tested Configuration:
| Computer Type: | Laptop |
| Mother Board Revision: | 0x30c2 |
| BIOS: | 68YTT ver.F.01 |
| CPU: | AMD Turion™ 64 X2 Dual-Core Mobile Technology TL-64 2.2 GHz |
| RAM: | 1024 MB |
| Bus Type: | 1394 Firewire 4 USB Ports CardBus PCMCIA |
| Video Adapter: | AMD Radeon™ X1250 |
| Desktop Effect Enabled: | Yes |
| Power Management: | NO |
| Host Bus Adapter: | ATI® SB600 , Serial ATA (SATA) |
| Hard Disk Drive: | Hitachi GST HTS541616J9SA00 , Serial ATA (SATA) |
| CD/DVD: | HLDS DVDRAM GSA-4084N , IDE |
| Floppy Type: | Diskless |
| Test Kit: | System Certification Kit 6.1.0-0.28 |
Config Notes
| The wireless network device was not tested due to no Broadcom wireless drivers being available for Linux. ATI Radeon X1250 driver version 8.37.6 was installed and used according to instructions available at Novell (Open SuSE) http://en.opensuse.org/Howto/ATI_Driver. The driver can be obtained by visiting: http://ati.amd.com/support/drivers/linux/linux-radeon.html. The Activate 3D Acceleration box was greyed out but checked. Enable Desktop Effects button was not shown in Look and Feel section because 3D Acceleration was showing Disabled. Found instructions at http://en.opensuse.org/Using_Xgl_on_SUSE_Linux to set 3D Acceleration to Enabled by holding shift key and double clicking on Disabled next to 3D Acceleration. Click Enable Desktop Effects button then restart the Xserver system. Desktop effects were enabled manually by running the command "gnome-xgl-switch --enable-xgl", see http://en.opensuse.org/Using_Xgl_on_SUSE_Linux for more details. Remote monitor: FN+F4 does not function properly. Stopping and restarting Xserver is necessary to display remote monitor. i.e. run command init 3 from terminal, then when remote monitor appears, run command init 5. Suspend to disk hotkey not supported; 'powersave -U' does work on the command line. The command 'powersave -u' does suspend to RAM after setting /etc/powersave/sleep: SUSPEND2RAM_FORCE:"yes." Power management does not entirely function when desktop effects are enabled; the system tray icons for suspend to disk (hibernate) and suspend to RAM (sleep) disappear when desktop effects are enabled. |
Adapters and Drivers
| Broadcom® Broadcom NetXtreme Gigabit Ethernet Adapter (5787M) | |||||||||
| Driver Type: LAN Driver | File Name: tg3.ko | ||||||||
| File Date: 18-May-2007 | File Size: 117708 | ||||||||
| Checksum: cd28263a64698fff1abaf368caf7dca7 | |||||||||
|
|
|||||||||
| ATI® SB600 | |||||||||
| Driver Type: HBA Driver | File Name: ahci.ko | ||||||||
| File Date: 18-May-2007 | File Size: 33248 | ||||||||
| Checksum: ea7e75d035d1af7a259373a1c03906cb | |||||||||
|
|
|||||||||
| AMD Radeon™ X1250 | |||||||||
| Driver Type: Video Driver | File Name: fglrx_dri.so | ||||||||
| File Date: 11-Jun-2007 | File Size: 10288810 | ||||||||
|
|
|||||||||
The term YES CERTIFIED applies only to the exact configuration documented in this bulletin. Components including LAN adapters, host bus adapters and other individually YES CERTIFIED components may be exchanged for other YES CERTIFIED components. For more information on swapping YES CERTIFIED components, please access the following web page:
http://developer.novell.com/devres/system/policy/exchange.htm
For more information regarding the specific test configuration, please contact:
Hewlett Packard Company
Your local Hewlett-Packard
representative